Colorado Springs Roof Works

Gutter Installation for Colorado Springs Homes

Gutters catch the water that runs off your roof and carry it away from the walls and foundation. Around Colorado Springs, a home usually needs new ones when the old runs sag, leak at the joints, pull away from the fascia (the board along the roof edge), or get torn loose by snow sliding off the roof. If you have been searching for guttering near me, this page covers what good work looks like and what to ask before you hire anyone.

Signs your gutters are failing

  • Water spills over the front lip in a storm instead of going down the downspout.
  • Sections sag, or the hangers (the brackets that hold the gutter to the house) have worked loose.
  • Rust, cracks or steady drips show at seams and corners.
  • Puddles, washed-out soil or a damp basement appear where a downspout ends.

Snow causes much of this damage. In El Paso County, the building code plans for 43 pounds per square foot of ground snow at homes under 7,000 feet, and for homes 7,000 feet up or more, the figure rises to 57 pounds per square foot. Teller County uses that 57-pound figure for every structure. When a load like that slides off a roof, it can bend a gutter flat or pull it off the house. Snow that melts and refreezes at the cold edge can also build an ice dam. That's a ridge of ice that traps meltwater so it backs up under the shingles.

What gutter installation involves

  1. Check the roof edge. The installer replaces any soft or rotted fascia before hanging anything.
  2. Pick materials. Aluminum is the common choice. Steel stands up better to heavy snow, and copper costs more but lasts a long time. The gutters and downspouts should be sized for the roof area that drains into them.
  3. Remove the old system. Old gutters, hangers and fasteners come off, and holes in the fascia get filled.
  4. Set the slope. Each run tilts slightly toward its downspout so water does not sit and freeze.
  5. Hang and seal. Many installers form aluminum gutters on site from a coil, so long runs have joints only at corners. Hangers screw into solid framing and sit close together to carry snow and ice. Corners and end caps get sealed.
  6. Run the downspouts. Extensions or splash blocks carry water several feet from the foundation and away from walkways that could ice over.
  7. Test and clean up. Running a hose through the system shows leaks or low spots.

The price depends on total length, material, the number of corners and downspouts, the height of the house and any fascia repair. If your current gutters only need upkeep, see gutter cleaning.

Local rules and weather that shape the job

Gutters hang right below the roof's ice barrier. That's a waterproof sheet laid under the roofing at the eaves to keep backed-up meltwater out.

  • El Paso County above 7,000 feet: the sheet starts at the eave and runs up until it sits 24 inches or more past the outside wall.
  • Teller County: it starts at the lowest roof edge and reaches 72 inches or more inside the outside wall.
  • Woodland Park: asphalt shingle roofs and similar ones need that same 72-inch reach.

Fasteners and drip edge work at the eave should never cut or lift that sheet.

El Paso County's Appendix E calls for gutters and downspouts made of noncombustible material. Vinyl gutters are plastic, so where that rule covers your lot, choose aluminum, steel or copper instead. To find out which rules reach your address, phone the Pikes Peak Regional Building Department at 719-327-2880 or look up www.pprbd.org. In Teller County, the Building Division answers at 719-687-3048.

In Cripple Creek's Historic Overlay District, any change to the outside of a building needs approval from the Historic Preservation Commission, called a Certificate of Appropriateness. New gutters change how a building looks, so call the Building Department at (719) 689-3588, extension 1, before you order.

Many HOAs set gutter colors and styles, so get written approval before work starts. Colorado law voids any HOA rule that bans fire-hardened building materials.

Choosing who installs your gutters

Ask each installer:

  • Will you check and repair the fascia, and how is that priced?
  • What gutter size, metal and thickness do you plan?
  • What hangers will you use, and how close together?
  • How will you work at the eave without damaging the ice barrier?
  • Where will each downspout drain?

The written quote should list total length, material, color, gutter and downspout sizes, hanger type and spacing, fascia repair terms, cleanup, the price and the payment schedule. If the installer offers a workmanship warranty, get its terms in writing.

Next step

Send a request through the contact page. A local gutter installer then phones you to go over your home and the job. If water is already getting in at the roof edge, also read about roof leak repair.

More services

Questions about your project?